The problem with most Bluetooth speakers is that they’re hard to keep clean. If you want to keep your speaker looking and working like new, you need to take some time and properly clean it every now and then. Here are some tips for a quick and easy way how to clean a sticky Bluetooth speaker.
There are a few ways to clean a sticky Bluetooth speaker including using 90% isopropyl alcohol poured into a microfiber cleaning cloth for wiping the sticky content from your speaker or you can use baking soda with a toothbrush. Read more to learn the other methods.
You may be asking why you would need to clean a sticky Bluetooth speaker. The answer is simple: it will help with the device’s longevity (and yours).
Dust and dirt can collect in and around the speaker, which can lead to power being wasted as the device struggles to get an adequate amount of air through. Not only that, but dust and dirt can also cause static, sound quality degradation, and worse–malfunctions.
Related: The Ultimate Guide on How to Clean a JBL Bluetooth Speaker
Reasons why your speaker can get dirty
Bluetooth speakers are usually made out of silicone, plastic, or rubber. This material is used because it is easy to clean and durable. However, if you aren’t careful with your speaker, it will eventually get dirty from all the use.
The speaker can pick up dirt and grease from your fingers that rub off easily onto the speaker. This can cause your speaker to become sticky and a bit greasy as well.
There are a few ways that you can avoid this problem when it happens by taking some time to clean the surface of your speaker before it gets too dirty. You could also learn how to clean a Bluetooth speaker in case this happens while you’re not near home or any soap/water source.
People might not realize how quickly these speakers can get dirty and sticky from all of the use. It’s not uncommon for people to forget to clean their speaker until they have a big gathering and notice that it doesn’t sound as good as it usually does.
There are a few things that can cause your speaker to get so dirty and sticky including drinks spilling on the device, dust accumulating, pet hair, or anything else that might stick to it. As you use your speaker more and more, these things will just add up until your speaker is covered in grime.
How to clean your Bluetooth speaker and keep it clean
There are many ways to care for your Bluetooth speaker and keep it clean. One way is to use a damp cloth or spray cleaner with water on the speaker surfaces. You’ll want to avoid using abrasive cleaners as they can scratch the surface of your speaker.
Another way to clean your speaker is to use some kind of lubricant like WD-40, Vaseline, or silicone spray. These lubricants will help loosen up dirt and grime so you can clean them off more easily.
As a last resort, you can use a toothbrush and soap on the surface of the speaker if there is really tough dirt that won’t come off otherwise. This should only be done when other methods have not worked because you might end up scratching the surface if too much force is applied.
Using warm water and soap to clean sticky Bluetooth speaker
- Use warm water and soap to clean the outside of your speaker.
- Use a damp cloth to clean the inside of your speaker, which is where the most dirt can accumulate.
- If you want to get rid of stains, use bleach or hydrogen peroxide on a cotton ball and wipe down the surface.
- After you’ve cleaned up all of the dirt, use a dry cloth to dry off your speaker and make sure it doesn’t have any streaks.
- If you want to make your speaker look brand new, wipe down with rubbing alcohol for an extra cleaning boost.
Using 90% isopropyl alcohol on a microfiber cleaning cloth to clean sticky Bluetooth speaker
The other method to clean sticky Bluetooth speaker is by using 90% isopropyl alcohol on a microfiber cleaning cloth. You can find this at any local store, or you can use a 50/50 mixture of water and vinegar.
Soak the cloth in the mixture, then wipe down the surface of your speaker with it. This should remove any debris that has accumulated on it. If you have time, let it air dry before using it again.
Using baking soda, water and a toothbrush to clean sticky Bluetooth speaker
One of the most common methods to clean sticky Bluetooth speaker is using baking soda and water.
Simply combine a cup of water with two tablespoons of baking soda to create a cleaning solution. Liberally apply the solution to all surfaces of your speaker, including the crevice at the bottom where dirt and grime can often accumulate.
Once you’ve applied the solution, scrub it off with a toothbrush or other small brush (a toothbrush works best). Next, rinse your speaker with cold water until it is no longer sticky. Let it air dry for about an hour before use.
Using talcum powder to clean sticky Bluetooth speaker
If you want to clean sticky Bluetooth speaker, these are the steps you should take:
First, mix some talcum powder and water together.
Then, use a cloth to wipe down the outside of the speaker. Be sure not to use anything abrasive on the device.
Next, put a small amount of water into the container that holds your speaker’s water and put one tablespoon of dish soap in there. Use your hand or a cloth to swish around in this mixture and then rinse it off well with warm water.
Finally, once you have dried off the outside of your speaker, be sure to give it a good wipe down with a dry towel before putting it away.
How to keep a Bluetooth speaker clean
Many people don’t think of the care that speakers need. Fortunately, there are a few simple things you can do to keep your speaker clean.
- Make sure to charge it in an area with good air flow so that it doesn’t accumulate dust and lint when not in use as this will make it more difficult to clean later on.
- You should also store it in a place where it won’t get wet or dirty with liquids and particles, such as a kitchen or bathroom countertop or on the floor, but keep in mind that the speaker should be at least half a meter away from walls and furniture to allow for good airflow and avoid heating up too much.
- Use a damp cloth to remove any dirt when cleaning the speaker’s surface by wiping in one direction only without applying too much pressure since this could damage the rubber housing around the device.
- If your speaker is really dirty and sticky, using mild soap and water is recommended instead of rubbing alcohol which would dry out the rubber housing. Once you’ve cleaned off all of the dirt, let it air dry before putting back into storage or charging again.
Why clean a Bluetooth speaker?
It is important to keep your speaker clean and dry. If you don’t, it can cause mold, fungi, and bacteria to grow and all of these things can be very harmful to your health, not to mention a huge nuisance. Plus, it will look so much better if it’s clean.
Clean up your Bluetooth speaker the next time you’re caught in a sticky situation with these tips:
- Wipe down the outside of the speaker with a bicarbonate soda solution – This removes any dirt or grime
- Spray the inside of the speaker with warm soapy water for about 10 seconds
- Take some bicarbonate soda on your fingertips and wipe over any stubborn spots
- Rinse off any residue from both sides with warm soapy water – You may need to do this process more than once depending on how dirty your speaker is.
Why should I clean a sticky Bluetooth speaker?
Cleaning your Bluetooth speaker is important because you want your music to sound as good as possible. It’s also important because you don’t want dirt and grime to build up on it, which can interfere with the wireless connection.
How to remove stickiness from a speaker
If your speaker is looking a little bit dirty and sticky, you can use some simple household supplies to make it look new again. First, start by wiping down the surface of the device with a damp cloth or paper towel.
This will remove any dirt or dust that might be stuck on the speaker. Then, take some rubbing alcohol and pour it on the cloth or paper towel. Rub this over the surface of your speaker to get rid of any remaining dirt and grease from cooking oils or fingerprints.
The next step is to sprinkle baking soda lightly over any sticky areas on your Bluetooth speaker. The baking soda will help scrub off any residue that might be left behind after cleaning with a cloth or paper towel and rubbing alcohol.
Finally, wipe down the entire surface of your speaker with a clean cloth or paper towel to remove any lingering baking soda residue. You’ll find that when you’re finished, your speaker looks as good as new!
How to clean sticky rubber speaker
The first thing you’ll want to do is remove the rubber protective cover from your speaker. This can be done by gently sliding your fingernail around the edge of the rubber until it pops right off.
Next, use a damp cloth to wipe down the front and back of the speaker. Make sure you go over every inch of it so that it’s fully cleaned. You might see some residue coming off in the process but that’s totally normal.
Now, all you’ll need to do is put the rubber cover back on. If you want, you can also clean up any extra water or residue with a dry paper towel or rag before putting it back on for good! Your speaker should be as good as new.
There are many ways to clean your Bluetooth speaker, but we’re going to give you the most basic steps. Before you start cleaning, make sure that the speaker is not connected to any device.
You don’t want to accidentally turn on a device and damage it while cleaning. First, create a mixture of equal parts of water and rubbing alcohol in a bowl or container.
Then, take your damp cloth and dip it into the mixture. Rub the cloth onto the rubber surface of your speaker until it is clean. If some stubborn stains still remain, use baking soda mixed with water and scrub again with a damp cloth just as before.
Finally, rinse out the cloths in between each side of the speaker until they are completely clean, and dry them off before putting them away.
How to remove sticky residue from speaker
If your speaker has sticky residue, you can try a few things to get it clean. First, start by dampening a cotton cloth with water or warm water and dish soap. You could also use an ammonia-based window cleaner.
After you’ve wet the cloth, gently scrub the surface of the speaker until the residue starts to come off.
If you have any tough spots, try using a toothbrush to loosen up the dirt and grime before wiping it off with your cotton cloth.
Once all of the residues are gone on your speaker, give it a good shake to get rid of excess water before you put it back in its case.
Using a damp cloth to remove sticky residue from speaker
There are three simple steps to removing sticky residue from your speaker. First, you should use a dry cloth or paper towel to soak up any excess liquid.
Next, use a slightly damp cloth or paper towel with a gentle soap to scrub the area.
Finally, rinse the area and dry it off with a clean cloth before plugging it in and turning it back on.
This is the easiest way to remove sticky residue from your wireless speaker.
Should I use water to clean a Bluetooth speaker?
No matter the speaker, you should never use water to clean it. The electronics inside a Bluetooth speaker can be easily damaged by moisture. This is especially true for wireless Bluetooth speakers that are not waterproof.
FAQs
How do I clean my speaker?
To clean your speaker, use a damp cloth and then wipe it down with soap and water. You can also use rubbing alcohol to remove any grease or other dirt that might have accumulated on it.
Is my speaker waterproof?
In general, most wireless speakers are not waterproof. However, some companies will design their speakers to be waterproof or water-resistant. If you want to keep your speaker protected from the elements, make sure that the company you’re buying the speaker from is selling one that is designed to be waterproof or water-resistant.
Should I put my speaker in a bag?
When storing your speaker, you should place it in a bag while you’re not using it so that it doesn’t get dirty or damaged. Damaged speakers can sound much worse than they did before they were damaged since the parts become loose and might rattle inside the casing. The last thing you want is for customers to think your product is defective when really it’s just dirty. Once your Bluetooth speaker gets dirty after being stored without a bag, then cleaning with soap and water will help remove any dirt and grime on the outside of the device so it can work like new again.
How often should I clean my Bluetooth speaker?
You should clean your speaker at least once every month. However, you can clean it more often or less often depending on the status of the speaker. If it’s dusty, then you need to wipe it clean as soon as possible. Of course, this depends on how often you use it and how much time you spend outside in the elements. If you live in a very humid climate, then you may want to clean it more often than that.
Is there an easy way to clean my sticky Bluetooth speaker?
Yes, all you need is a soft brush or cloth and some vinegar or alcohol. Just wipe the surface of your wireless speaker with the cloth and mild solution, let the surface dry, and then give it another wipe.
Does a dirty speaker get spoilt easily?
Yes, a dirty speaker can get spoilt easily. A dirty, sticky speaker will have bacteria and dust all over it. So, if you’re not cleaning your speaker every time you use it then there is a good chance that it will be spoilt before too long.
Conclusion
Keeping your speaker clean is important because it will last longer and work better.
It doesn’t take much to clean a speaker, just a damp cloth, some soap and water, and a lot of patience.
It’s a good idea to take care of your speakers, so you can enjoy them for longer.
So now that you know how to clean your sticky speaker, you should feel confident that your speaker will be clean and ready to go whenever you want to use it.
There are many different ways to clean your speaker, but the most important thing is to be sure to maintain your speaker periodically so it doesn’t get too dirty. Allowing dirt and grime to stay on your speaker will cause it to wear down faster than if you were to regularly clean it.